Dahua Wireless PIR-Camera Motion Detector (2MP)
R1,699.00 Incl. VAT
The Dahua DHI-ARD1731-W2(868) is an indoor wireless PIR motion detector with a built-in 2MP camera for visual alarm verification. When an intrusion is detected, it captures high-resolution images and sends them through a compatible Dahua alarm hub, allowing users to assess the alarm event without continuous video recording.
- 12 m PIR detection range across an 86° angle when installed at the recommended 2.2 m height.
- 2MP image verification: JPEG snapshots up to 1600 × 1200 resolution, with an 88° horizontal camera viewing angle.
- Infrared illumination: Up to 12 m for image capture in low-light and dark conditions.
- Pet immunity: Up to 18 kg, with three adjustable PIR sensitivity levels.
- Wireless communication: 868 MHz alarm signalling up to 1,600 m and 2.4 GHz RF-HD image transmission up to 300 m in open-space conditions.
- Battery powered: Includes 3 × CR123A batteries, with a manufacturer-rated battery life of up to four years under specified low-activity conditions.
- Additional protection: AES128 encryption, two-way communication, frequency hopping, tamper detection, temperature monitoring and low-battery alerts.
- Compatibility: Requires a Dahua ARC3000H or ARC3800H series alarm hub. ARA43 series repeaters cannot relay PIR-camera images.
Description
Dahua DHI-ARD1731-W2(868) Wireless PIR-Camera Motion Detector
Knowing that an alarm has been triggered is useful. Being able to see what caused it is even better. The Dahua DHI-ARD1731-W2(868) brings these two functions together in a single wireless indoor detector, combining passive infrared motion detection with a built-in 2MP camera for visual alarm verification.
When the detector identifies an intrusion, its integrated camera captures high-resolution snapshots and transmits them through a compatible Dahua alarm hub. The images can then be viewed through the Dahua DMSS mobile application or a supported alarm receiving centre, helping users and security personnel assess what has happened before deciding how to respond.
Unlike a conventional surveillance camera, the ARD1731-W2(868) is designed for event-based image capture rather than continuous video monitoring. This makes it particularly useful as part of a wireless alarm installation where photographic evidence of a triggered sensor is more important than uninterrupted recording.
Motion Detection with Visual Verification
The detector covers an area up to 12 metres at an 86° detection angle when installed at the manufacturer’s specified height of 2.2 metres. Its three adjustable sensitivity levels allow installers to adapt detection behaviour to the room, while digital temperature compensation helps maintain detection performance under changing environmental conditions.
Pet immunity is rated for animals weighing up to 18 kg, helping reduce unwanted alarms in suitable indoor installations. Actual performance depends on the installation position, animal movement and surrounding conditions.
The integrated 2MP CMOS camera captures JPEG images at resolutions up to 1600 × 1200 pixels. Its 88° horizontal and 68° vertical field of view provides visual coverage of the monitored area, while built-in infrared illumination supports image capture up to 12 metres in darkness.
Dahua’s RF-HD transmission technology enables high-resolution images to be transferred efficiently, with the manufacturer specifying transmission of six 1600 × 1200 images in up to 10 seconds under suitable conditions. The system also supports a one-week cloud cache for images and videos.
Wireless Communication and Alarm System Compatibility
The ARD1731-W2(868) uses two wireless communication methods. Its 868 MHz radio connection carries alarm signalling and device communication, with a published open-space range of up to 1,600 metres. A separate 2.4 GHz RF-HD connection handles high-speed image transmission, with an open-space range of up to 300 metres.
These ranges are laboratory-style open-space figures rather than guaranteed indoor distances. Walls, reinforced structures, electrical interference and the positioning of the alarm hub can affect signal quality and image transmission speed.
Two-way wireless communication, frequency hopping and AES128 encryption protect the communication process. The detector also provides tamper alerts, battery-status reporting, wireless signal testing, temperature monitoring and support for remote firmware updates.
Important compatibility requirement: This detector is designed for compatible Dahua ARC3000H and ARC3800H series alarm hubs. It is not a standalone Wi-Fi camera and cannot operate independently as a complete security system. Dahua ARA43 series repeaters do not support forwarding its captured images to the alarm hub, so the detector must be positioned where reliable image communication is available.
Battery Operation and Indoor Installation
The detector operates from three CR123A batteries, eliminating the need to run a separate power cable to the installation position. Dahua specifies a battery life of up to four years based on approximately two activations per week and 70% battery efficiency. Frequent alarms, image transmissions, testing and environmental conditions can reduce actual battery life.
The wall-mounted design is intended for indoor use in homes, offices and similar protected environments. Installers should position the detector at approximately 2.2 metres above floor level, maintain an unobstructed detection area and avoid locations exposed to direct sunlight, heat sources or unstable environmental conditions.
Before completing installation, the detector should be paired with the compatible alarm hub and both the radio and RF-HD signal strengths tested. Dahua recommends a signal indication of at least two bars at the chosen position. The camera’s snapshot test can then be used to confirm that the captured images cover the intended area.
What’s in the Box
- 1 × Dahua DHI-ARD1731-W2(868) Wireless PIR-Camera Detector
- 3 × CR123A batteries
- 1 × Double-sided adhesive tape
- 2 × Screw packages
- 1 × QR code card
- 1 × Quick Start Guide
- 1 × Legal and regulatory information document
Downloads & Documentation
Specifications
Product Information
- Brand: Dahua
- Model: DHI-ARD1731-W2(868)
- Product Type: Wireless PIR Motion Detector with Camera
- Application: Indoor intrusion detection and visual alarm verification
- Compatible Alarm Hubs: Dahua ARC3000H and ARC3800H series
- App Integration: Dahua DMSS through a compatible alarm hub
PIR Motion Detection
- Detection Technology: Passive Infrared (PIR)
- Detection Range: Up to 12 m
- Detection Angle: 86°
- Recommended Installation Height: 2.2 m
- Detection Speed: 0.3–3 m/s
- Sensitivity: 3 adjustable levels
- Pet Immunity: Up to 18 kg
- White Light Resistance: 2,000 lux
- Digital Temperature Compensation: Supported
Camera and Image Verification
- Image Sensor: 2MP CMOS
- Maximum Resolution: 1600 × 1200 pixels
- Selectable Image Resolutions: 1600 × 1200, 1280 × 960, 640 × 480, 320 × 240
- Image Format: JPEG
- Camera Field of View: 88° horizontal, 68° vertical
- Illumination: Infrared
- Infrared Range: Up to 12 m
- Day/Night Imaging: Colour / Black and white
- Image Transmission: RF-HD technology
- Image Transmission Performance: Up to 6 images at 1600 × 1200 within 10 seconds under suitable conditions
- Cloud Cache: One-week cache for images and videos
Wireless Communication
- Alarm RF Frequency: 868.0–868.6 MHz
- RF-HD Frequency: 2.4 GHz
- Maximum RF Range: Up to 1,600 m in open space
- Maximum High-Speed RF-HD Range: Up to 300 m in open space
- Communication: Two-way wireless
- Encryption: AES128
- Frequency Hopping: Supported
- RF Signal Testing: Supported
- RF-HD Signal Testing: Supported
- Wi-Fi Specification: IEEE 802.11b/g/n, 2.4 GHz
- RF Transmitter Power: EIRP limit 25 mW
- Repeater Restriction: ARA43 series cannot forward PIR-camera images to the hub
Power and Security Functions
- Power Supply: 3 × CR123A batteries
- Battery Life: Up to 4 years, based on 2 activations per week and 70% battery efficiency
- Standby Current: 65 µA
- Low Battery Detection: Supported
- Battery Level Display: Supported
- Tamper Detection: Supported
- Temperature Monitoring: Supported
- Status Indicator: 1 × Green LED
- Power Switch: 1 × On/Off switch
- Remote Firmware Updates: Supported
- Update Failure Recovery: Supported
Environmental and Physical Specifications
- Installation: Indoor wall mounting
- Operating Temperature: -10°C to +55°C
- Operating Humidity: 10–90% RH
- Product Dimensions: 71.0 × 53.2 × 127.6 mm (manufacturer-listed dimensions)
- Net Weight: 202 g
- Casing Material: PC + ABS
- Security Classification: EN 50131 Grade 2
- Environmental Class: Class II
- Certification: CE









